Isuzu Questions and Answers
Post your Isuzu question or share what you know by answering questions
Get your questions answered by the AutoMD Community.
Share your expertise and help others with vehicle questions.
Browse Isuzu Categories
1996 Isuzu Hombre XS 4 Cyl 2.2L
Engine - by rfddon 10/13/2013Battery not charging
stop charging bat symbol came on
2001 Isuzu Rodeo S V6 6 Cyl 3.2L
Brakes - by judy 9/26/2013Master cyclinder was replaced, but I have a bad brake fluid leak. does this master cyclinder have a gasket
a gasket that needs to be replace and where can I get it
1993 Isuzu Rodeo LS 4 Cyl 2.6L
Preventive Maintenance - by adriennegrimmer 9/25/2013Where is the inertia safety shut off switch located?
1995 Isuzu Rodeo LS 6 Cyl 3.2L
Preventive Maintenance - by hopebme 9/25/2013What type and weight of oil is required for the rear axles?
2000 Isuzu Trooper LS 6 Cyl 3.5L
Engine - by Ray 9/17/2013Po401 egr code map sensor no change volts
170,000 work good all around except po401 code you erase and back after 5 miles, clean EGR valve check map sensor is ok but don't change volt always the same 5.06 volt I test it with a hand vacuum and from 5 psi to 20 is no change I don't know where to located the ...
1989 Isuzu Amigo XS 4 Cyl 2.6L
Engine - by timmcalexander69 9/10/2013Where is the ignition module located
I can't find it
1995 Isuzu Rodeo LS 6 Cyl 3.2L
Engine - by glack45 9/8/2013My truck is lacking power and acceleration. I've tried a bunch of different things.. Nothing has worked... Help?
230,000 miles. Standard, Original clutch no slippage. EGR replaced, wire harness replaced altenator replaced. I can accelerate great 1st and 2nd, but when I hit 3, 4 and 5 gear, it's sluggish. When it hits roughly 2500 rpm the power spikes, but by then I have to ...
1994 Isuzu Pickup S 4 Cyl 2.6L
Transmissions & Drivetrains - by kennymoen2 8/31/2013Transfer case problom
I took apart my transfer case to seal it a gold gear fell out so I put it back I it were I though it goes and put it all back together and now the truck will not move
2004 Isuzu Ascender Limited 6 Cyl 4.2L
Engine - by rogsimons 8/6/2013AC/recirculate switches.
When the ac or recirculate switches are turned on the engine rpms drop to almost stalling, then rise again to normal, 5 or 6 seconds later, drops again, repetitively. When the AC compressor clutch engages the rpms drop,then comes back up when disengages
1994 Isuzu Trooper LS 6 Cyl 3.2L
Transmissions & Drivetrains - by slc5280 8/1/2013My car will not exceed 40 mph in drive and it makes a knocking noise below 2000 rpm.
150k miles, regular oil/maint visits. No event before problem started. Two repair shops, no fix, but new belts, hoses, water pump re: knocking noise. Automatic trans good in first and second gear, slow to engage above & does not exceed 40mph. Reverse is good. ...
1992 Isuzu Rodeo LS 6 Cyl 3.1L
Engine - by jamesstacksforests 7/22/2013Why is my crankshaft having such a hard time of turning when I attempt to start the engine?
My Rodeo has 110k mileage, I replaced the valve cover gaskets three weeks ago and the drive belt because it had been making a "whoooo" sound. I drove it a couple times after and it ran fine, but with reduced "whooo". Two das ago I cranked it and went on the city ...
2004 Isuzu Ascender LS 6 Cyl 4.2L
Engine - by idnim1 7/6/20132004 Isuzu Ascender engine light on with red arrow pointing down?
2004 Isuzu Axiom S 6 Cyl 3.5L
Body & Interior - by nicolasrolly 7/1/2013How to replace doors actuators
just find out the door is not responding on the remote somebody told me it;s the door actuators is the problem
1993 Isuzu Pickup S 4 Cyl 2.6L
Engine - by joe 7/1/2013Engine starts then stalls
1993 Isuzu Pu’p, 2.6L, Fuel injection, automatic. about 110,000 miles. I purchased this truck new, its been great, no problems until a year ago. Then O2 light came on. I changed the O2 sensor twice. Checked all the wiring including the red wire all the way to the ...
1995 Isuzu Trooper S 6 Cyl 3.2L
Engine - by jkmay52 6/17/2013Coolant is pouring from the rear of my engine,it's not hoses. what could it be ?
I have replaced all hoses, and the o-rings on the tube that runs under the manifold. the coolant runs out as soon as I put it in. The engine does not have to be running.