» View Question
dwwilson

dwwilson 4/1/2019

2005 Dodge Dakota SLT 8 Cyl 4.70L

Engine

Why is it overheating?

My Dakota is overheating. All usual suspects have been checked off. New thermostat new pump new radiator cap. Clutch fan works. No leaks. Gaskets and block are fine. Radiator and block have been flushed water is flowing fine. Heater blows hot air. It still overheats but if you turn on the heater it goes back to normal temp and is fine as long as the heater is on. Any ideas?

2 Answers


Jimm

Jimm 12/31/2019

Loss of coolant because of a coolant leak is probably the most common cause of engine overheating. Possible leak points include hoses, the radiator, heater core, water pump, thermostat housing, head gasket, freeze plugs, automatic transmission oil cooler, cylinder head(s) and block.

Make a careful visual inspection of the entire cooling system, and then PRESSURE TEST the cooling system and radiator cap. A pressure test will reveal internal leaks such as seepage past the head gasket as well as cracks in the head or block. A good system should hold 12 to 15 psi for 15 minutes or more with no loss in pressure. If it leaks pressure, there is an internal coolant leak (most likely a bad head gasket but possibly also a cracked cylinder or engine block).

It is important to pressure test the radiator cap, too, because a weak cap (or one with too low a pressure rating.

1. Perform a cooling system / radiator pressure test when the engine is cold - as a first step to locate the leak.
Obtain a loaner tool / free radiator pressure tester from the local auto parts stores such as Autozone, O'Reilly, NAPA, Advance Auto, or PepBoys. Follow their instructions and pump it to an adequate air pressure 12 -15 psi or the pressure rating listed on the radiator or reservoir cap. Observe the leaks and perform the repair.
Note: do not over pressurize beyond the pressure allowed by the radiator cap, then test the radiator cap as well.

2. Air pockets trapped in the cooling system can cause the engine to overheat. Some cooling systems have air bleed valves built into the system to aid in the removal of air pockets. Advice: For many cooling systems, the method of removing air pockets is to start the engine and allow it to run with the radiator cap off or loose until all the air escapes from the neck of the radiator. For some systems this method is not sufficient, and the manufacturer has installed air bleed valves usually near or on the thermostat housing.

Reply
0
Jimm

Jimm 12/31/2019

Loss of coolant because of a coolant leak is probably the most common cause of engine overheating. Possible leak points include hoses, the radiator, heater core, water pump, thermostat housing, head gasket, freeze plugs, automatic transmission oil cooler, cylinder head(s) and block.

Make a careful visual inspection of the entire cooling system, and then PRESSURE TEST the cooling system and radiator cap. A pressure test will reveal internal leaks such as seepage past the head gasket as well as cracks in the head or block. A good system should hold 12 to 15 psi for 15 minutes or more with no loss in pressure. If it leaks pressure, there is an internal coolant leak (most likely a bad head gasket but possibly also a cracked cylinder or engine block).

It is important to pressure test the radiator cap, too, because a weak cap (or one with too low a pressure rating.

1. Perform a cooling system / radiator pressure test when the engine is cold - as a first step to locate the leak.
Obtain a loaner tool / free radiator pressure tester from the local auto parts stores such as Autozone, O'Reilly, NAPA, Advance Auto, or PepBoys. Follow their instructions and pump it to an adequate air pressure 12 -15 psi or the pressure rating listed on the radiator or reservoir cap. Observe the leaks and perform the repair.
Note: do not over pressurize beyond the pressure allowed by the radiator cap, then test the radiator cap as well.

2. Air pockets trapped in the cooling system can cause the engine to overheat. Some cooling systems have air bleed valves built into the system to aid in the removal of air pockets. Advice: For many cooling systems, the method of removing air pockets is to start the engine and allow it to run with the radiator cap off or loose until all the air escapes from the neck of the radiator. For some systems this method is not sufficient, and the manufacturer has installed air bleed valves usually near or on the thermostat housing.

Reply
0

Answer this question

( characters left)

Follow Question

what's this?
advertisement
advertisement