Auto Answers » Body & Interior » Pontiac » Page 7

Pontiac body & interior repair questions and answers

Post your Pontiac body & interior question or share what you know by answering questions

842 Questions
Sort by:
  • h3hummer
    h3hummer - 2005 Pontiac G6 - Body & Interior - 2/26/2013
    I have water leak in car back seat and font seat what is the problem
     
    0 answer
  • jacquelinewazhere
    jacquelinewazhere - 2003 Pontiac Aztek - Body & Interior - 2/24/2013
    REAR END BUMPER- MY DAUGHTERS FATHER MY AUNT AND DAUGHTER WHERE HIY FROM BEHIND BUMPER IS HANGING AND I HAVE UP BODY DAM
    I I WANTED TO GET A ESTIMATE OF THE PARTS COST.. AS WELL AS THE LABOR TO REPAIR THE DAMAGE
     
    • Jimm
      2/24/2013 Jimm
      Quoting online without seeing the damage is impossible to do with any accuracy. Visiting a trusted and peputable paint and body shop in the local area is your best bet.
  • dewayne
    dewayne - 1997 Pontiac Sunfire - Body & Interior - 2/24/2013
    Low beam head lights not working
    have changed bulbs and checked power have power to the plug what else can i check for low beam to work
     
    0 answer
  • dakfieldmarshal
    dakfieldmarshal - 2002 Pontiac Montana - Body & Interior - 2/23/2013
    Windshield wipers do not park correctly
    I understand this is a quic fix involving removing the rubber drip rail and the plastic cover then moving some clip on the wiper transmission, do you have pics that show exactly how to do this?
     
    • CVO
      2/23/2013 CVO
      I don't have the pics.
      To correct the wiper arms back to their original rest position, make sure the wiper arms are in their off state.
      Pop the plastic cap out of the wiper shaft, use a 15 mm open wrench to remove the nut. Pry the wiper arms out of their spline shaft and re-position them down to the bottom of the windshield.
      CVO
      2/23/2013 HouseCallAuto
      CVO, this is incorrect.
    • HouseCallAuto
      2/23/2013 HouseCallAuto
      No, this is not the case at all. The wiper parking issue that happens on the Montana / Venture / Silhouette is caused by a faulty Wiper Motor Crank Arm Assembly. Replace it. ACDelco 12494825 Windshield Wiper Motor Crank Arm Assembly, no other brands are available. Probability here is 100%.
  • Ray
    Ray - 2006 Pontiac G6 - Body & Interior - 2/18/2013
    Winshield Wipers Fail to work
    Wiper frozen to winshield were turned on and did not engage after just flinching in a short motion
     
    0 answer
  • jake6383
    jake6383 - 1999 Pontiac Grand Prix - Body & Interior - 2/17/2013
    Heater fan wont work,keeps blowing fuse
    can feel heat.problem is with fan
     
    • HouseCallAuto
      2/17/2013 HouseCallAuto
      Unplug the blower motor, install a new fuse and if the new fuse now does not blow, then your cause is a bad blower motor. If the fuse still blows even with blower motor unplugged then your cause is a shorted blower motor resistor or a burned and shorted out connector or both.
  • cdeads8
    cdeads8 - 1999 Pontiac Grand Am - Body & Interior - 2/12/2013
    Why is key not working every time i try to turn on
    also i have no dash lights, i purchased new key and the new one works better but still wont start everytime. it feels like it blocked
     
    • HouseCallAuto
      2/12/2013 HouseCallAuto
      Please clarify what you mean exactly, because saying your key is not working is not specific enough. Are you saying that the key sometimes does not turn (as though it is the wrong key) or do you mean the key turns but the engine does not start? I am taking what you said to mean that the key does not rotate at all sometimes. If this is the case then the fix would be to replace the ignition lock cylinder. Even though you made a new key, the problem is with the tumblers inside the lock cylinders itself. The new cylinder would have to be coded to match the old cylinder before you install it and then a simple programming procedure has to be done before the vehicle will recognize the new cylinder. If you will attempt to do this yourself with a repair manual next to you, let me know and I can provide the add'l details you will need to do so you can do this job without outside help from a mechanic. This job is not a simple slam dunk DIY type job and requires you follow a very specific procedure or when you finish the car will still not run and if you code the cylinder wrong the key will still not turn.
  • jhun
    jhun - 1996 Pontiac Sunfire - Body & Interior - 2/12/2013
    How to replace a new muffler
    How to install a new muffler
     
    • CVO
    • Arlinw
      2/12/2013 Arlinw
      Step 1: Raise the car and safely support its weight on a floor jack
      Step 2: Use penetrating lubricants such as PB Blaster or WD-40 around the bolts, and tapping the flanges with a hammer (or wrench) to let the lubricant penetrate through the rust.
      Step 4: Raise the muffler from its mounting posting by pulling it free of the hangers with your hands.
      Step 5: Unbolt the muffler and lower it with the floor jack. Remove the gaskets that seal the two sections of exhaust.
      Step 6: Use some automotive cleaner to clean the forward mating surfaces of the exhaust to prepare them for re-installation.
      Step 7: Balancing the new muffler on the floor jack, raise it until you can easily fasten it to the forward sections of the exhaust system and attach it with the new nuts and bolts provided. Hang the new muffler from the body of the vehicle with new exhaust hangers. Slide the new hangers over the mounting brackets on the muffler and the car body, lowering the floor jack until the muffler is at its proper height. Then retighten the bolts that were loosened before, leaving the new muffler firmly mounted onto your vehicle, and remove the floor jack.
      For more information on motorcycle exhausts visit http://4wheelonline.com/.../...e_Exhausts.171021
  • motorhommie
    motorhommie - 1987 Pontiac Fiero - Body & Interior - 2/10/2013
    How do I connect a new cigarette lighter on a 1994 Ford Explorer?
    Part was disconnected so I don't know which terminals to connect the 2 spade clipped wires to.
     
    • CVO
      2/10/2013 CVO
      The hot wire of the cigarette lighter is an orange ( ORG ) wiring connected to a 25 A fuse, the other wiring ( BLK ) is connected to the chassis ground.

      See this Fig. Fig. 8 Chassis wiring-1987-88 models
      http://www.autozone.com/.../...rGuideContent.jsp
      CVO
      2/10/2013 CVO
      Ignore this answer, it's for a 1987 Pontiac Fiero.
      CVO
      2/10/2013 CVO
      The cigarette hot wire ( LB/W ) is connected to the 20 A fuse, the other wiring ( BK ) is connected to the chassis ground.
      Use this 1994\FM\FMWR94EXPL014a as a reference to access the wiring diagrams @ http://www.bbbind.com/free_tsb.html
  • scooter11
    scooter11 - 2007 Pontiac Vibe - Body & Interior - 1/26/2013
    How do I fix my radio and power source?
    Shorted out my radio and power source when I tried to plug in a busted plug in from my GPS.
     
    0 answer
  • scooter11
    scooter11 - 2007 Pontiac Vibe - Body & Interior - 1/21/2013
    When plugging in my gps it seemed like there was a short, now the radio doesn't work and there is no display.
    I tried changing the fuse that would fix this problem but I'm not positive i changed the correct fuses.
     
    0 answer
  • tasteelers1
    tasteelers1 - 1987 Pontiac 6000 - Body & Interior - 1/19/2013
    How to change headlamp bulb?
    Is it twist fitted or should it pull straight out?
     
    • Jimm
      1/19/2013 Jimm
      They are easy to replace - open the hood, and behind the front headlight - on the housing - you'll see the lamp socket. Simply, turn the socket to remove the socket from the headlamp housing. Once the socket is removed, then twist out the headlamp bulb and replace with a new one. The installation is the reverse of the removal.
      Try the 'How-To-Guides' feature on the AutoMD website for the specific steps - with photos.
  • bjthien
    bjthien - 2006 Pontiac Grand Prix - Body & Interior - 1/15/2013
    Why do my bright lights come on when my turn signal turns offf
    My bright lights come on after I complete my turn and the turn signal goes off
     
    0 answer
  • Rob
    Rob - 1999 Pontiac Grand Am - Body & Interior - 1/14/2013
    Driver side window stopped working
    Window will not move up or down
     
  • ynotgram
    ynotgram - 2001 Pontiac Aztek - Body & Interior - 1/12/2013
    Is the rear trunk supposed to LIFT UP AUTOMATICALLY when the button is pushed?