Auto Answers » Body & Interior » Mercury » Page 23

Mercury body & interior repair questions and answers

Post your Mercury body & interior question or share what you know by answering questions

395 Questions
Sort by:
  • ford
    ford - 1997 Mercury Sable - Body & Interior - 10/26/2010
    I need to replace my drivers door window is there any specailty tools needed for this job.
    the sable is a four door
     
    • Bobby
      10/26/2010 Bobby
      you will need a trim panel removal tool. it has a screw driver handle but a flat end to help prty the clips that hold the door panel in place. I'm not sure if the window is held on with rivets some are so you may need a drill to remove the old rivets, and a riveting gun to install the new window.
  • Bobbie
    Bobbie - 2001 Mercury Mountaineer - Body & Interior - 10/25/2010
    Have 2 doors that won't open
    One door will open only if you click over and over inside, then let the window and use outside latch to open. The other will not open inside at all and it's hard to open on the outside. What could be the problem with these doors?
     
    • AWACS E3 Sentry
      10/25/2010 AWACS E3 Sentry
      Once you open you interior door panel, you will be able to find out what the problems is. What happened to me with my car is when i try to open the passenger side door from the outside, there is no resistance so its obvious what the problem was.

      Now there are 2 screws on the interior door handle, remove them. Then remove the inside door handle cup. On low series front door trim panel, remove the screw and the window regulator handle. Start in a lower corner and work around the panel and separate the front door trim panel from the front door to disengage the pin-type retainers.

      Lift the front door trim panel to disengage the top lip from the weatherstrip.

      Position the front door trim panel aside.

      Separate the power window switch finish panel from the door trim panel.
      Then release the locking tabs.

      If equipped, remove the courtesy lamp bulb from the lens and remove the front door trim panel.





  • dmack1
     
    • MOONSTER_TOOLZ
      10/18/2010 MOONSTER_TOOLZ
      The wiper arm has a nut that can be removed (maybe, 17mm socket) to release the arm, and then you can adjust the wiper arm reach.
  • becca
    becca - 1999 Mercury Grand Marquis - Body & Interior - 10/15/2010
    Interior dimmer switch
    interior dimmer switch doesn't work
     
  • cheryl
    cheryl - 1999 Mercury Sable - Body & Interior - 10/14/2010
    I am tring to locate the GEM were it is on a 1999 ford sable
     
    • AC130 Spectre
      10/14/2010 AC130 Spectre
      The GEM module on your model is attached to the fuse box under the dash on the drivers side. You will have to remove the fuse box then take the screws loose and the module will come off. The fuse box is very easy to remove on these cars, just a few nuts holding it on and a few wiring harnesses to take loose.
  • anna
    anna - 2007 Mercury Grand Marquis - Body & Interior - 10/11/2010
    Need guide to replace and install side mirrow
     
    • darkmind
      10/11/2010 darkmind
      You can pry at the top end of the side mirror cover, and then removed it in an upward direction after you unsnapped the clips. If there is a sponge present remove it to expose the mirror area. There are 3 nuts holding the side view mirror to the door before you remove it disconnect the wiring harness/ connector (just pull the tab outward and pull apart).

      You can also visit this link to have more idea how to replace a mirror http://www.automd.com/.../
  • anna
    anna - 2007 Mercury Grand Marquis - Body & Interior - 10/11/2010
    How to remove inside door panel
    need to take off panel on door to connect electrical wires for side mirrow (mirrow got broken)
     
    • darkmind
      10/11/2010 darkmind
      Is it necessary to removed your inside door panel to replace your side mirror?

      You can pry at the top end of the side mirror cover, and then removed it in an upward direction after you unsnapped the clips. If there is a sponge present remove it to expose the mirror area. There are 3 nuts holding the side view mirror to the door before you remove it disconnect the wiring harness/ connector (just pull the tab outward and pull apart).
  • Jamie
    Jamie - 1995 Mercury Cougar - Body & Interior - 10/11/2010
    Domelights stay on when driving, doorjam switches are good. I need to find a dashlight dimmer switch, but cannot locate
    Can that switch be bypassed at all to keep my domelights from staying on? Nobody anywhere seems to have this part. Ford is not making mercury parts anymore.
     
    0 answer
  • SANMAN
    SANMAN - 2000 Mercury Grand Marquis - Body & Interior - 10/8/2010
    WHY DOES MY CARS WINDSHIELD FOG UP WHEN I PUT THE HEAT ON
     
  • Larry G. Beaudrot
    Larry G. Beaudrot - 2008 Mercury Grand Marquis - Body & Interior - 10/8/2010
    Your estimate states rear body panel can be bought from your online partner, Auto Parts Warehouse. How do i do this.
    Do I go through you folks are what. I've recently started doing major body repairs and mechanicals also, I would like to partner up with you. I'd like to know the cost to join your services. Please advise a.s.a.p.
     
    • darkmind
      10/8/2010 darkmind
      On the estimated feature of AutoMD at the total price just click the buy online icon and you can get or purchased it on the Autopartswarehouse.

      And if you own an auto service shop and you like to advertise your business to the users in AutoMD just click this link http://www.automd.com/user/shop_registration on the get started just click the click here to register your shop and the AutoMD will validate or verify something first and then your shop will be added in the AutoMD Shop Directory for FREE.
  • gibsonpapa
    gibsonpapa - 1997 Mercury Villager - Body & Interior - 10/8/2010
    HOW TO REPLACE HINGE OF DOOR
  • S
    S - 1997 Mercury Mountaineer - Body & Interior - 10/7/2010
    How do you remove the door panels to repair outside handle?
     
    • Pave Low
      10/7/2010 Pave Low
      1. Disconnect negative battery cabe
      2. Carefully detach the door handle bezel
      3. Pry out the front edge of the armrest switch control plate and disconnect the electrical connectors then remove the retaining screw from the opening
      4. Remove the lower trim panel retaining screws
      5. Once all the screws are removed grasp the trim panel at the switch opening and pull it up and out.Disconnect the power mirror electrical connector
  • Mark Lemley
    Mark Lemley - 2006 Mercury Grand Marquis - Body & Interior - 10/7/2010
    What is wrong w/ my A/c?
    I turn on the automatic a/c system to auto and the fan come on while making a noise and the cold air come out of the vents on top of the dash and also out of the floor vents. I can sometimes switch to normal or max air and then back to auto and the cold air will ...
     
    • yboy82
      10/7/2010 yboy82
      What have you done so far to fix the issue with your car a/c? Did you already check the condition of your car a/c switch? It may be defective. You can use the Find a Shop feature of AutoMD to see a list of shops near you with their address, telephone # and labor rate per hour.
  • Jim
    Jim - 1990 Mercury Topaz - Body & Interior - 10/6/2010
    My heater fan quit running, not getting power to fan switch
    my fan quit and need it for winter heat
     
    0 answer
  • HENRY QUINLEY
    HENRY QUINLEY - 1995 Mercury Sable - Body & Interior - 9/30/2010
    WHO MANUFACTURED PART #F2DB-5462187-CWA 84-110
    MATERIAL BRITTLE. COVERS LEFT SIDE OF DRIVERS SEAT. HOUSES POWER SEAT CONTROLS AND LUMBAR BUTTON. VIN=1MELM5348SA610138.
     
    • HouseCallAuto
      9/30/2010 HouseCallAuto
      This is a Ford part number. Call a Ford dealer parts dept and ask if it is still available if you have not done that yet. They can run the part # and will be able to check the current inventory of every Ford dealer in the USA.
 
AutoMD Verified Customer
AutoMD obtained proof this customer interacted with the shop.