Auto Answers » Body & Interior » Lexus » Page 6

Lexus body & interior repair questions and answers

Post your Lexus body & interior question or share what you know by answering questions

287 Questions
Sort by:
  • Deondra
    Deondra - 1996 Lexus SC400 - Body & Interior - 5/8/2012
    What wires can I unplug from the back of the radio to disconnect the factory disc changer in the trunk?
    Wire to the disc changer are pinched and causes the fuse for the radio to blow. I need to know what to do to disconnect the disclosed to the disc changer coming from the radio. Car wrecked passenger rear right above the tire
     
    0 answer
  • Bill
    Bill - 1992 Lexus SC400 - Body & Interior - 4/25/2012
    Speedometer fluctuating, searching
    tachometer still works
     
    0 answer
  • shutton
     
    • shutton
      4/22/2012 shutton
      Sorry. That should have been RB501607 and RB501608.
  • sheph
    sheph - 1999 Lexus GS300 - Body & Interior - 4/20/2012
    A bout the CAT SIS 2010a
    http://www.youtube.com/watch?v=NJU1kgY28pU&context=C4366478ADvjVQa1PpcFP-YPDOHB85FwTx7GrLiOKgGnMcT_79uck=
     
  • sheph
    sheph - 1999 Lexus GS300 - Body & Interior - 4/20/2012
    How to set MB sd connect C4 local area connection and administration parameter
    http://www.xcardiag.com/wholesale/mb-sd-connect-compact-4-star-diagnosis-with-multi-language-39.html
     
  • Bob
    Bob - 2004 Lexus ES330 - Body & Interior - 4/18/2012
    The SRS idiot light is on caused by a failed sensor in the front passenger seat. How do you replace the sensor?
    When a person sits in the front passenger seat the seatbelt warning does not come on indicating that it doesn't detect the person sitting there.
     
  • rena
    rena - 1999 Lexus GS400 - Body & Interior - 4/15/2012
    Car want crank. it got a new starter&alternator on it
    i had it jumpd off it crunk right up.but after i drove it . i wudnt crank back up, 5hrs later i dont have no warning lights on.& the power window controls on the driver side nothing works but the one 4 my window.the button works on the other doors but powers locks ...
     
    0 answer
  • robert
    robert - 1993 Lexus SC300 - Body & Interior - 4/11/2012
    The radio dint come on as i turn ignision on .
    after i drove it for abaut 2 mile or 3 mile...the radio come on..after that it come on after i stop for several hours..just didnt come on..after an over nite stop . ty for ur respond
     
    0 answer
  • allencd
    allencd - 1995 Lexus LS400 - Body & Interior - 4/4/2012
    Hvac blower alternates from high to low speed
    When I set my blower to high it will blow at high for about 30 seconds then cut back to low for a few minutes. Cold it be the blower motor resistor?
     
    0 answer
  • allencd
    allencd - 1995 Lexus LS400 - Body & Interior - 4/3/2012
    Where is the hvac blower motor resistor located
     
    • yboy82
      4/3/2012 yboy82
      Check under the dashboard (glove box) if you can't see a rectangular shape with electrical connector on it, then you have to remove your blower motor housing to see the blower motor resistor.
      yboy82
      4/3/2012 allencd
      my blower alternates from max to low ( blows max for maybe 30 seconds then back to low for maybe 3 mins ). Do you think it could be the resistor
  • bording
    bording - 2003 Lexus RX300 - Body & Interior - 4/2/2012
    Replace left passenger door lock actuator
    Left passenger door lock actuator does not always work
     
    • EG9 K20A3
      4/2/2012 EG9 K20A3
      You will have to remove the door trim to gain access to the bolts and connector.

      DISASSEMBLY


      1. REMOVE DOOR INSIDE HANDLE BEZEL

      1. Open the cap, then remove the screw.
      2. Using a screwdriver, remove the inside handle bezel. HINT: Tape the screwdriver tip before use.



      2. REMOVE POWER WINDOW SWITCH Using a screwdriver, remove the panel as shown in the illustration. HINT: Tape the screwdriver tip before use.




      3. REMOVE DOOR TRIM

      1. Using a screwdriver, remove the courtesy light, then disconnect the connector. HINT: Tape the screwdriver tip before use.
      2. Remove the 4 screws and 2 clips.
      3. Insert a screwdriver between the trim and door panel to pry the door trim. HINT: Tape the screwdriver tip before use.
      4. Release the claws, then remove the inner weatherstrip from the door trim.



      4. REMOVE INSIDE HANDLE Remove the screw and inside handle, then disconnect the 2 cables.

      Hope this helps.

      Hello,

      You will have to remove the door trim to gain access to the bolts and connector.

      DISASSEMBLY


      1. REMOVE DOOR INSIDE HANDLE BEZEL

      1. Open the cap, then remove the screw.
      2. Using a screwdriver, remove the inside handle bezel. HINT: Tape the screwdriver tip before use.



      2. REMOVE POWER WINDOW SWITCH Using a screwdriver, remove the panel as shown in the illustration. HINT: Tape the screwdriver tip before use.




      3. REMOVE DOOR TRIM

      1. Using a screwdriver, remove the courtesy light, then disconnect the connector. HINT: Tape the screwdriver tip before use.
      2. Remove the 4 screws and 2 clips.
      3. Insert a screwdriver between the trim and door panel to pry the door trim. HINT: Tape the screwdriver tip before use.
      4. Release the claws, then remove the inner weatherstrip from the door trim.



      4. REMOVE INSIDE HANDLE Remove the screw and inside handle, then disconnect the 2 cables.

      Hope this helps.

      Hello,

      You will have to remove the door trim to gain access to the bolts and connector.

      DISASSEMBLY


      1. REMOVE DOOR INSIDE HANDLE BEZEL

      1. Open the cap, then remove the screw.
      2. Using a screwdriver, remove the inside handle bezel. HINT: Tape the screwdriver tip before use.



      2. REMOVE POWER WINDOW SWITCH Using a screwdriver, remove the panel as shown in the illustration. HINT: Tape the screwdriver tip before use.




      3. REMOVE DOOR TRIM

      1. Using a screwdriver, remove the courtesy light, then disconnect the connector. HINT: Tape the screwdriver tip before use.
      2. Remove the 4 screws and 2 clips.
      3. Insert a screwdriver between the trim and door panel to pry the door trim. HINT: Tape the screwdriver tip before use.
      4. Release the claws, then remove the inner weatherstrip from the door trim.



      4. REMOVE INSIDE HANDLE Remove the screw and inside handle, then disconnect the 2 cables.

      Hope this helps.
  • Patrick D
    Patrick D - 2001 Lexus RX300 - Body & Interior - 3/31/2012
    My Air conditioning vent door flaps loudly and repeatedly when the air conditioner comes on and starts blowing air.
    The vent flapping open and close repeatedly sounding like flipping a deck of cards between your hands. This only occurs when the AC starts up after sitting idle a while and ends after a period of between 3 and 5 minutes of multiple vent shutter movement.
     
    0 answer
  • Lorelei
    Lorelei - 1993 Lexus SC300 - Body & Interior - 3/26/2012
    How do I attach new regulator to bottom of window? Saw your video, but did not show how regulator was actually put on w
    There is a metal piece on window presently being held up with wood piece. How do I set the window on regulator, which bolts does it attach to?
     
    0 answer
  • JJ
    JJ - 1997 Lexus ES300 - Body & Interior - 3/16/2012
    One headlight is dim while the other shines normal
     
    • yboy82
      3/16/2012 yboy82
      Try to check for battery voltage and ground at headlight electrical connector with a multitester on the dim headlight. If battery voltage is present, trace the ground circuit for the headlamp electrical connector, then clean and repair as necessary.

      And if the voltage at the headlight electrical connector is significantly less than the voltage at the battery, refer to the headlight wiring diagram of your vehicle to troubleshoot and locate the voltage drop.
  • JJ
    JJ - 1997 Lexus ES300 - Body & Interior - 3/16/2012
    One headlight shines very dim
     
    • yboy82
      3/16/2012 yboy82
      Try to check for battery voltage and ground at headlight electrical connector with a multitester on the dim headlight. If battery voltage is present, trace the ground circuit for the headlamp electrical connector, then clean and repair as necessary.

      And if the voltage at the headlight electrical connector is significantly less than the voltage at the battery, refer to the headlight wiring diagram of your vehicle to troubleshoot and locate the voltage drop.
 
AutoMD Verified Customer
AutoMD obtained proof this customer interacted with the shop.