Auto Answers » Transmissions & Drivetrains » Dodge » Page 6

Dodge transmissions & drivetrains repair questions and answers

Post your Dodge transmissions & drivetrains question or share what you know by answering questions

Browse Dodge Categories

1450 Questions
Sort by:
  • pjkoegel
    pjkoegel - 2000 Dodge Ram 1500 Van - Transmissions & Drivetrains - 11/11/2013
    Auto transmission slips in high gear and stays there
    323000 miles,none check engine light is on the code is P 1740 I already know its the 4th clutch pressure switch but want to know where it is located
     
    0 answer
  • AutoMD Member
    AutoMD Member - 2000 Dodge Ram 1500 - Transmissions & Drivetrains - 11/6/2013
    Is the speedometer controlled by the rear wheel sensors?
    Check engine light, brake light, abs light tripped, transmission quit shifting properly, outside temperature gauge quit working properly and both speedometer/odometer quit functioning. I have replaced the ECM and speed sensor on the tranny and the shifting problem ...
     
    • HouseCallAuto
      11/6/2013 HouseCallAuto
      Replace the differential mounted wheel speed sensor in the rear. I suggest you get one from Dodge because there have been many defects with aftermarket sensors for this application. There is only one sensor.
  • DONALD REECE
    DONALD REECE - 2007 Dodge Caliber - Transmissions & Drivetrains - 11/6/2013
    How do I check the transmission fluild level
    automatic transmission
     
    • CVO
      11/6/2013 CVO
      This vehicle does not have a transmission fluid dipstick. These types of transmissions are designed to be maintenance free. In order to check the transmission fluid, your vehicle likely has check valve on the bottom of the transmission on the bottom of your car. Your car must be level when the fluid is checked and therefore having a mechanic with a hydraulic lift or underground bay check your transmission fluid.
  • DONALD REECE
    DONALD REECE - 2007 Dodge Caliber - Transmissions & Drivetrains - 11/4/2013
    How do i check the transmission fluild level,and add fluild if i need too?
    adding transmission fluild.
     
    • HouseCallAuto
      11/4/2013 HouseCallAuto
      Has to go on a lift so you cant do it. Take out sight plug on side of tranny. Car has to be level.
  • Sammy_Jr
    Sammy_Jr - 2002 Dodge Stratus - Transmissions & Drivetrains - 10/31/2013
    Ok I have got these codes the other day P0734(Gear 4 Incorrect Ratio). P0700, P0846,P0871.
    I have change the input and output speed sensor. My check engine light goes off, but it's still skipping a little, and started making a weird noise.
     
    • HouseCallAuto
      10/31/2013 HouseCallAuto
      When the cause is not input shaft and output shaft sensors, its the tranny itself. Start tryin to make a deal on a rebuilt tranny.
  • AutoMD Member
    AutoMD Member - 2002 Dodge Grand Caravan - Transmissions & Drivetrains - 10/24/2013
    Where is the clicking noise coming from and is it possible to fix for cheap
    put car into reverse a clicking noise, give the car gas clicking noise then it goes away after giving it gas
     
    0 answer
  • AutoMD Member
    AutoMD Member - 2002 Dodge Caravan - Transmissions & Drivetrains - 10/24/2013
    When i shift my car in reverse is like clicking noise when i go into drive there is a clicking when i press on the gas2
    the noises go away after the car gets going but when i give it gas it clicks and go away please help
     
    0 answer
  • AutoMD Member
    AutoMD Member - 2000 Dodge Intrepid - Transmissions & Drivetrains - 10/21/2013
    Why did the speedometer stop working at the same time the car will not shift out of 1st gear?
    There were no other signs of transmission problems prior to this occurring. The speedometer stopped working and it does not shift out of first gear at all, but will go into reverse.
     
  • AutoMD Member
    AutoMD Member - 2011 Dodge Caliber - Transmissions & Drivetrains - 10/18/2013
    Why will my shifter will not go into drive.
    there's 12000 miles on my car and we've owned it for less than 6 months. last night i had no problems. today the shifter will not go into drive. i comes out of park and goes through reverse (engages no problem) and neutral. locks up before going into drive. anything ...
     
    • HouseCallAuto
      10/18/2013 HouseCallAuto
      The car is too new for any knowledge about a cause. I'm sure the dealer sees it often and will know the cause right away. Older models needed to have shifter assemblies replaced, many under warranty for similar issues. Take to dealer for quickest turnaround time. This is NOT a DIY type repair and will require the use of a factory scan tool.
  • AutoMD Member
    AutoMD Member - 1998 Dodge Durango - Transmissions & Drivetrains - 10/18/2013
    WHAT COULD BE THE PROBLEMS IF THE TRANSMISSION IS STUCK IN DRIVE AND WANT SWITCH TO ANY OTHER GEAR
    THE ONLY GEARS IT WILL GO IN IS PARK AND DRIVE
     
    0 answer
  • Sammy_Jr
    Sammy_Jr - 2002 Dodge Stratus - Transmissions & Drivetrains - 10/16/2013
    Today my check engine light came on with this code P0734(Gear 4 Incorrect Ratio). What does this mean?
    It also came with three other codes at the same time.
     
    • HouseCallAuto
      10/16/2013 HouseCallAuto
      Why didn't you post the 3 other codes?
      HouseCallAuto
      10/16/2013 Sammy_Jr
      Sorry!! The other three codes are P0700, P0871,P0846
    • HouseCallAuto
      10/16/2013 HouseCallAuto
      If you replace the input shaft speed sensor and the output shaft speed sensor you *may* solve this. I suggest you do this yourself though because if it doesn't you wu=ill need about $1800 to pay for rebuilding the tranny. The sensors are very cheap and not hard to replace and besides even if it don't solve it the new sensors will get used when the tranny is redone.
      HouseCallAuto
      10/23/2013 Sammy_Jr
      Hi, I want to thank you for the advise. It fixed the problem also it was reasonably price to fix.
  • mfo152
    mfo152 - 2001 Dodge Ram 1500 - Transmissions & Drivetrains - 10/15/2013
    Dodge ramwont go into park
    everything else is fine
     
    0 answer
  • pfeiffer4
    pfeiffer4 - 2003 Dodge Durango - Transmissions & Drivetrains - 10/12/2013
    What would be the average cost to replace a governor pressure solenoid and transducer>
    Getting a P1757 code on my Durango. Having a problem shifting.. Just started this morning. Would rev at high RPM but not shift when accelerating between 35 and 45 MPH. Does not happen all the time.Vehicle has less than 80,000 miles on it.
     
    • frankiedonnn
      10/12/2013 frankiedonnn
      Hi pfeiffer4, Check with a dodge dealership.In 2006 the transducer, solenoid, filter valve and gasket were replaced on my dodge ram van, and it came to : $267 for parts and $247 for labour.The miles on my dodge ram was 81,395 at the time so it seems to be common with dodge.I'm looking at a Bob Wilson Dodge receipt . I keep the receipts for all my repairs.
  • howieh
    howieh - 2003 Dodge Ram 2500 - Transmissions & Drivetrains - 10/7/2013
    Vibration at 70 mph hole truck vibrates worse on excel decell
    2003 dodge 153000 miles 5.9 turbo diesel replaced rear u joint and left wheel bearing also replaced right wheel joint at 70 mph hear this vibration and feel it in seat, steering wheel and seat can't tell if it from the front or rear more when going up hills and ...
     
    • HouseCallAuto
      10/7/2013 HouseCallAuto
      One of the front (left or right) outer joints is frozen or you have a driveshaft ujoint that is frozen or loose.
      HouseCallAuto
      10/8/2013 howieh
      found the right wheel joint bad and in the process of changing that I also changed the right wheel hub and bearing seems to have solved the problem Thank you Housecallauto
  • cycles
    cycles - 2007 Dodge Caravan - Transmissions & Drivetrains - 10/7/2013
    How to fix backup lights
    bulbs are good
     
    0 answer