Auto Answers » Body & Interior » Dodge » Page 5

Dodge body & interior repair questions and answers

Post your Dodge body & interior question or share what you know by answering questions

1372 Questions
Sort by:
  • AutoMD Member
    AutoMD Member - 2010 Dodge Journey - Body & Interior - 12/15/2013
    Heater blower stop working
    blower just stop with no warning,what should I be doing to track this problem
     
    • HouseCallAuto
      12/15/2013 HouseCallAuto
      *probably* has a bad blower motor resistor. Check and see if blower motor terminals are receiving battery voltage on one wire of the plug and a ground on the other wire of the plug with the engine running and heater and blower turned on highest speed (just use a 12 volt test light) and if there is battery voltage but no ground then the cause is likely a bad blower motor resistor.
  • Shooter54us
    Shooter54us - 2002 Dodge Ram 1500 - Body & Interior - 12/15/2013
    How hard is it to replace front door weather strip seals?
    Hear air leaking in around top of door when traveling at high speeds.
     
    • Jimm
      12/15/2013 Jimm
      Not difficult to replace, the seals either press in to place, or use weatherstrip sealant to secure. The parts are readily available; try these on-line sources; www.partsgeek.com, www.rockauto.com, www.discountautoparts.com, www.autopartswarehouse.com, www.jcwhitney.com - to list only a few possibilities.
      In fact, they (RockAuto) list the front door weatherstrip from around $27.00 (each side; left or right) for your vehicle
  • Shooter54us
    Shooter54us - 2002 Dodge Ram 1500 - Body & Interior - 12/15/2013
    How hard is it to replace front weather strip door seals?
    Can hear air blowing in around front door seals.
     
    0 answer
  • AutoMD Member
    AutoMD Member - 2005 Dodge Dakota - Body & Interior - 12/5/2013
    When i turn off windshield wipers they dont stop all the way down.
    my wipers stop an inch or two from the bottom of the windshield. they then cycle once when i turn the key on and again after starting the truck. this happens most of the time. they return up from the normal off position an inch or two.
     
    0 answer
  • AutoMD Member
    AutoMD Member - 2001 Dodge Grand Caravan - Body & Interior - 12/2/2013
    Why do all of my lights and gauges stop working every time I turn on a turn signal?
    We replaced the wiring harness and ECU last year and just put a new battery in last night. Been having some starting issues for several months now and were told it was because our battery was low.
     
    • HouseCallAuto
      12/2/2013 HouseCallAuto
      When did this issue begin? You did not clarify if I am to believe it has existed since the wiring harness and ECU was done. Which wiring harness was replaced. The answer cannot be vague. The wiring that connects what components together?
      HouseCallAuto
      12/3/2013 AutoMD Member
      The issue began right after we replaced the battery last night. The info I know about the wiring harness that was replaced last year is that it needed replaced because the previous wires had been placed over the exhaust manifold (resulting in melting, grounding, and a shorted out ECU). The new one was put in but with the wires going under instead of over.
  • AutoMD Member
    AutoMD Member - 1993 Dodge Ramcharger - Body & Interior - 12/1/2013
    Replace power window regulator an motor left side
    has a counter balance spring an need to know how to set spring tension on sector gear?
     
    • CVO
      12/1/2013 CVO
      WINDOW LIFT MOTOR INSTALLATION INSTRUCTIONS
      Window regulators may vary in design. It will be necessary to obtain a shop manual for
      safe removal, installation and handling of window regulators.
      CABLE TYPE REGULATORS
      IMPORTANT: Some regulator cable spools will unravel if not handled properly. Refer to
      Service Manual for proper removal of Motor from cable spool. Cable style regulators
      require special handling for successful removal and installation of the window lift motor.
      These instructions will help prevent the spool from coming apart and resulting in the
      complete replacement of the motor/regulator assembly.
      • Remove the regulator according to the shop manual. Make sure to support the window
      glass in a safe manner.
      • Unbolt or remove the retaining rivets holding the motor to the regulator.
      • CAREFULLY lift the motor up out of the spool since some spools will come out of the
      housing with the motor. HINT: use a long thin screwdriver to help separate the motor
      from the spool.
      • Remove the motor.
      • Reverse the procedure to install.
      SCISSOR STYLE REGULATORS
      Scissors style regulators have an assist spring to help move the window glass. This spring
      is under pressure at all times. The regulator must be secured BEFORE removing the motor.
      • Remove the regulator according to the shop manual. Make sure to support the window
      glass in a safe manner.
      • BEFORE removing the motor from the regulator it will be necessary to secure the sector
      gear of the regulator by installing a bolt through the regulator body and the sector gear.
      • Drill out any rivets or remove any bolts retaining the motor to the regulator.
      • Reverse the procedure to install.

      Note: not sure if the spring tension has been released yet, hope this helps.
  • AutoMD Member
    AutoMD Member - 1997 Dodge Caravan - Body & Interior - 10/22/2013
    How do i remove the door lock on the passenger door, the part the key goes in? I've already disassembled everything
    else off of it.
     
    • CVO
      10/22/2013 CVO
      Door locks removal and installation.
      See this Fig. Fig. 2: After removing the retaining clip, pull the lock cylinder straight out from behind the handle assembly @ www.autozone.com
  • AutoMD Member
    AutoMD Member - 2009 Dodge Ram 1500 - Body & Interior - 10/22/2013
    Why does my heat/cool fan make a clicking sound when the key is turned on and off?
    The heat / cool fan is not working. I am getting heat but the fan is not working.
     
    • CVO
      10/22/2013 CVO
      1. Apply a 12 volts direct to the blower motor connector, if the blower motor doesn't run, replace the blower motor.
      2. In the event the blower motor does run, check the blower motor resistor and the Module Totally Integrated Power, they're both link to the blower motor.
  • AutoMD Member
    AutoMD Member - 2001 Dodge Ram 2500 - Body & Interior - 10/19/2013
    Need help making replacement lights work
    replacing stock head lights with Spyder PRO-YD-DR94-HL-AM-C. High beam indicator will not go off. When all 4 head lights are in they go very dim. The low beam stock light positive drops from 12 to 1.5 volts the Spyder low beam side only drops to 5.8. In the off ...
     
    0 answer
  • 03vette
    03vette - 2008 Dodge Dakota - Body & Interior - 10/15/2013
    When I turn on the turn signal it blinks in both directions back and fouth
    have changed out both rear bulbs,the front ones work ok
     
    0 answer
  • 03vette
    03vette - 2008 Dodge Dakota - Body & Interior - 10/15/2013
    The turn signals go back and forth from boths sides when I turn 1 on have turn off then back off ,still goes back a fort
    changed the bulbs only for the turn signal only
     
    0 answer
  • bajvaughn22
    bajvaughn22 - 1999 Dodge Durango - Body & Interior - 10/9/2013
    Driver side mirror
    In July of this year I ordered a driver side mirror from you. The part number was 51481, but it is too large to fit my mirror.
     
    • HouseCallAuto
      10/9/2013 HouseCallAuto
      Contact customer service at the site directly where you ordered it from. This is a forum and has no ability to oversee orders placed on the parts site.
  • jojofriedrich
    jojofriedrich - 2004 Dodge Stratus - Body & Interior - 9/30/2013
    I was in a car accident recentely and the airbags deployed with right fender impact. What should I expect to spend?
    240,000 miles, just purchased tires 12hrs prior to the accident.
     
    0 answer
  • pattyjose1
    pattyjose1 - 2011 Dodge Avenger - Body & Interior - 9/30/2013
    Air bags not deploying do to a rear impact at 70 mph
    my air bags not open at 70 mph rear collision my car is total lucky to be alive is it normal
     
    0 answer
  • dcrugg
    dcrugg - 1996 Dodge Dakota - Body & Interior - 9/24/2013
    Head lights/high beams go on and off.
    While driving my high beams will go on and off by themselves. I have changed out the switch and it worked for a short time, but now they are doing the same thing. what could this be?
     
    • n2tropicals
      9/24/2013 n2tropicals
      Im having the same problem on my dodge dakota sport 2002 p/u
      Its the low beams doing this and it drained my battery dead and useless.
      I hope someone can help us-
      Mechanic said bad battery but its still doing it with a new battery and a single mom of 3 , I just need some help. I cant afford to go back to the mechanic for a while , if I only knew whats causing it
      sherry