Auto Answers » Body & Interior » Dodge » Page 3

Dodge body & interior repair questions and answers

Post your Dodge body & interior question or share what you know by answering questions

1350 Questions
Sort by:
  • AutoMD Member
    AutoMD Member - 2006 Dodge Ram 1500 - Body & Interior - 2/9/2014
    Only get heat out of the defrost and dash no floor heat
    can hear motor run when changing the dial but still no heat on floor
     
    • HouseCallAuto
      2/9/2014 HouseCallAuto
      You most likely have a faulty mode door actuator. there is an actuator that moves the air direction between the panel vents and the floor. It is not moving. The mode actuator in question is noted as #1 in the link I provided you for reference but the picture I linked here is for a ac / heater system that has "dual-zone" option. The single zone system which you likely have would be the mode actuator furthest left (of the two marked by a "1")
  • Jose
    Jose - 2006 Dodge Charger - Body & Interior - 2/7/2014
    I have the ac/heater off and I still feel a breeze shooting threw the vent when the car is moving?
    How can't I tell if the fresh air door of the ac/heater is working and if broken where can I buy the part
     
    • Jimm
      2/7/2014 Jimm
      Here is a Dodge TSB (technical service bulletin) that may help;

      NUMBER: 24-014-05 REV. A
      GROUP: Heater & A/C
      DATE: November 19, 2005

      THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 24-014-05, DATED August 11, 2005, WHICH SHOULD BE REMOVED FROM YOUR FILES ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDES THE ADDITION OF AN APPLICABILITY NOTE.

      SUBJECT:
      Hot Air From A/C Ducts At Start Up and/or A/C System Doesn't Cool After Extended Driving In Hot And Humid Ambient Conditions OVERVIEW:
      This bulletin involves replacing the HVAC Manual Temperature Control.

      MODELS:
      2006 (LX) 300/Charger/Magnum
      NOTE :**This bulletin applies to vehicles built prior to August 12, 2005 and equipped with manual A/C (sales Code HAA).**

      SYMPTOM/CONDITION:

      While operating the vehicle with the A/C on, the vehicle operator notices that after a vehicle start sequence there is a hot blast of airflow from the A/C vents and/or the vehicle operator notices that after a vehicle start sequence that the doors inside of the HVAC unit appear to be moving or calibrating. The vehicle operator may also notice a loss of airflow from the vents and becomes uncomfortably warm after a long drive in hot and humid weather while operating with the A/C on.

      DIAGNOSIS:

      If the vehicle operator describes the Symptom/Condition, perform the Repair Procedure.

      PARTS REQUIRED: Part #55111870AH Control Manual A/C


      REPAIR PROCEDURE:
      1. Remove I/P center bezel using the fiber stick to pry up the bezel without damaging the I/P padding.
      2. Disconnect electrical connectors for the A/C control, switch bank and clock if equipped.
      3. Remove the four 4 mm screws attaching the A/C control and remove the A/C control.
      4. Install revised manual A/C control, p/n 55111870AH. Tighten the screws to 2 Nm (17 in. lbs.).
      5. Connect the A/C control, switch bank and clock wiring connectors as equipped.
      6. Snap in the I/P center bezel to the center I/P.
      7. Start the vehicle. The HVAC doors will calibrate upon the initial start up of the vehicle.

      POLICY:
      Reimbursable within the provisions of the warranty.
  • AutoMD Member
    AutoMD Member - 2008 Dodge Grand Caravan - Body & Interior - 2/6/2014
    How do I fix a turn signal problem?
    I have already replaced the bulb, but am still having the same result.
     
    • jdl
      2/6/2014 jdl
      Not enough info, which turn signal is it, front/back, right/left? Could be turn signal switch or wiring circuit. Did you check voltage and ground for the bulb?
      jdl
      2/6/2014 jdl
      Just to add, because your instrument cluster and totally integrated power module are involved with your turn signals, I'd have to check applicable trouble codes for those systems. Some of the national brand autostores will check codes for free. I just don't know if they will check B and U type codes?
    • HouseCallAuto
      2/6/2014 HouseCallAuto
      Yes, like jdl said, you have to clarify exactly what the turn signal problem is. I *might* be able to give you something to go on but need more details.
  • AutoMD Member
    AutoMD Member - 2010 Dodge Grand Caravan - Body & Interior - 2/4/2014
    Both power doors will not open manually or with power switch
    Vehicle has 77,780 miles on it. Passenger side rear power sliding door will not open with both manual or power switches. Nothing is locked with the Master lock. The door will open perhaps an inch but that is it. Will not open more than that. Can hear the motor on ...
     
    0 answer
  • AutoMD Member
    AutoMD Member - 1997 Dodge Caravan - Body & Interior - 1/9/2014
    Do I need to reprogram control for heater/ ventilation system? Or could something else have gone wrong?
    Car is in good condition and kept in heated garage. The heater/ ventilation control (hi/ bi-lev/ lo/ lo & defrost/ defost only) has worked fine since new - until an outing on the COLD January 7 we just endured! After the car sat outdoors for three hours, it ...
     
    • HouseCallAuto
      1/9/2014 HouseCallAuto
      Probably has a bad mode door actuator but this is a 6 hour job. The only programming procedure there is relating to the HVAC system is what is called a cool-down test but if that test were needed there would be leds blinking wildly on the wiper buttons and heater / ac buttons.
  • AutoMD Member
    AutoMD Member - 2007 Dodge Ram 1500 - Body & Interior - 1/4/2014
    How to replace headlight assemblies on my pick up
    I need to r and r both headlight assemblies on my 2007 dodge ram 1500. both are severely discolored and cloudy . How do I accomplish this.
     
    • Jimm
      1/4/2014 Jimm
      Generally you first raise the hood on the truck. Then, locate the the screws on the top and side of the headlight that hold it in place and remove them. Next unplug the wire connection on the rear of the headlight housing.
      Next, you should be able to slide the headlight out with some force.

      The parts are readily available; try these on-line sources; www.partsgeek.com, www.rockauto.com, www.discountautoparts.com, www.autopartswarehouse.com, www.jcwhitney.com - to list only a few possibilities. In fact they (RockAuto) list the replacement headlight assemblies from around $64.00 for your vehicle.
    • CVO
      1/4/2014 CVO
      See this url and select the product for your need.
      https://www.google.com/search

      I use 3M Headlight Restorer and my headlights look like new again.
      CVO
      1/5/2014 AutoMD Member
      I know how to replace old style headlights. This is not just a headlight replacement it is an assembly replacement. So if anyone knows how to remove the headlight assembly on this truck please advise.
      CVO
      1/5/2014 CVO
      This site doesn't have an instruction yet to remove the headlights of your specific vehicle, but just take a look to get an idea with other similar cars
      http://www.bodyshopzone.com/.../index.html.
  • Tim
    Tim - 1991 Dodge Dakota - Body & Interior - 1/2/2014
    Light around key hole won't go off?
    The light that is around the key hole won't go off when I turn the car off, it stays on continuously. Would this be causing my repeated dead battery?
     
    • HouseCallAuto
      1/2/2014 HouseCallAuto
      The key illumination is on the same circuit as the interior lights which of course illuminate when any door is opened. You did not mention anything about interior / courtesy lamps remaining on so I am assuming that they are not, but it could mean that a door jamb switch is no good (remaining active when door is closed) and that the interior light bulbs are all either missing bulbs or the bulbs are burned out. And yes that will kill your battery. Does this vehicle have a time delay feature that turns off interior lights after like 15 seconds or so after taking key out and closing the door?
      HouseCallAuto
      1/3/2014 Tim
      I pulled the fuse on the interior lights yesterday, my overhead lamp was shot. I just went out there and she turned over just like normal. That seemed to have been the culprit! Glad she is fixed!
  • AutoMD Member
    AutoMD Member - 2003 Dodge Ram 2500 - Body & Interior - 12/20/2013
    How to replace heater fan motor?
    How do I remove and replace the cabin heater fan and motor? what is the part number for the above motor?
     
    • Jimm
      12/20/2013 Jimm
      The blower motor replacement is easy. Look under the dash on the pasenger side, and you can see it. Its just three screws that hold it in, and unplug it. Then just replace the new one in position.

      The parts are readily available; try these on-line sources; www.partsgeek.com, www.rockauto.com, www.discountautoparts.com, www.autopartswarehouse.com, www.jcwhitney.com - to list only a few possibilities.
      In fact, they (RockAuto) list the blower motor from around $39.00 for your vehicle.
  • AutoMD Member
    AutoMD Member - 2010 Dodge Journey - Body & Interior - 12/15/2013
    Heater blower stop working
    blower just stop with no warning,what should I be doing to track this problem
     
    • HouseCallAuto
      12/15/2013 HouseCallAuto
      *probably* has a bad blower motor resistor. Check and see if blower motor terminals are receiving battery voltage on one wire of the plug and a ground on the other wire of the plug with the engine running and heater and blower turned on highest speed (just use a 12 volt test light) and if there is battery voltage but no ground then the cause is likely a bad blower motor resistor.
  • Shooter54us
    Shooter54us - 2002 Dodge Ram 1500 - Body & Interior - 12/15/2013
    How hard is it to replace front door weather strip seals?
    Hear air leaking in around top of door when traveling at high speeds.
     
    • Jimm
      12/15/2013 Jimm
      Not difficult to replace, the seals either press in to place, or use weatherstrip sealant to secure. The parts are readily available; try these on-line sources; www.partsgeek.com, www.rockauto.com, www.discountautoparts.com, www.autopartswarehouse.com, www.jcwhitney.com - to list only a few possibilities.
      In fact, they (RockAuto) list the front door weatherstrip from around $27.00 (each side; left or right) for your vehicle
  • Shooter54us
    Shooter54us - 2002 Dodge Ram 1500 - Body & Interior - 12/15/2013
    How hard is it to replace front weather strip door seals?
    Can hear air blowing in around front door seals.
     
    0 answer
  • AutoMD Member
    AutoMD Member - 2005 Dodge Dakota - Body & Interior - 12/5/2013
    When i turn off windshield wipers they dont stop all the way down.
    my wipers stop an inch or two from the bottom of the windshield. they then cycle once when i turn the key on and again after starting the truck. this happens most of the time. they return up from the normal off position an inch or two.
     
    0 answer
  • AutoMD Member
    AutoMD Member - 2001 Dodge Grand Caravan - Body & Interior - 12/2/2013
    Why do all of my lights and gauges stop working every time I turn on a turn signal?
    We replaced the wiring harness and ECU last year and just put a new battery in last night. Been having some starting issues for several months now and were told it was because our battery was low.
     
    • HouseCallAuto
      12/2/2013 HouseCallAuto
      When did this issue begin? You did not clarify if I am to believe it has existed since the wiring harness and ECU was done. Which wiring harness was replaced. The answer cannot be vague. The wiring that connects what components together?
      HouseCallAuto
      12/3/2013 AutoMD Member
      The issue began right after we replaced the battery last night. The info I know about the wiring harness that was replaced last year is that it needed replaced because the previous wires had been placed over the exhaust manifold (resulting in melting, grounding, and a shorted out ECU). The new one was put in but with the wires going under instead of over.
  • AutoMD Member
    AutoMD Member - 1993 Dodge Ramcharger - Body & Interior - 12/1/2013
    Replace power window regulator an motor left side
    has a counter balance spring an need to know how to set spring tension on sector gear?
     
    • CVO
      12/1/2013 CVO
      WINDOW LIFT MOTOR INSTALLATION INSTRUCTIONS
      Window regulators may vary in design. It will be necessary to obtain a shop manual for
      safe removal, installation and handling of window regulators.
      CABLE TYPE REGULATORS
      IMPORTANT: Some regulator cable spools will unravel if not handled properly. Refer to
      Service Manual for proper removal of Motor from cable spool. Cable style regulators
      require special handling for successful removal and installation of the window lift motor.
      These instructions will help prevent the spool from coming apart and resulting in the
      complete replacement of the motor/regulator assembly.
      • Remove the regulator according to the shop manual. Make sure to support the window
      glass in a safe manner.
      • Unbolt or remove the retaining rivets holding the motor to the regulator.
      • CAREFULLY lift the motor up out of the spool since some spools will come out of the
      housing with the motor. HINT: use a long thin screwdriver to help separate the motor
      from the spool.
      • Remove the motor.
      • Reverse the procedure to install.
      SCISSOR STYLE REGULATORS
      Scissors style regulators have an assist spring to help move the window glass. This spring
      is under pressure at all times. The regulator must be secured BEFORE removing the motor.
      • Remove the regulator according to the shop manual. Make sure to support the window
      glass in a safe manner.
      • BEFORE removing the motor from the regulator it will be necessary to secure the sector
      gear of the regulator by installing a bolt through the regulator body and the sector gear.
      • Drill out any rivets or remove any bolts retaining the motor to the regulator.
      • Reverse the procedure to install.

      Note: not sure if the spring tension has been released yet, hope this helps.
  • AutoMD Member
    AutoMD Member - 1997 Dodge Caravan - Body & Interior - 10/22/2013
    How do i remove the door lock on the passenger door, the part the key goes in? I've already disassembled everything
    else off of it.
     
    • CVO
      10/22/2013 CVO
      Door locks removal and installation.
      See this Fig. Fig. 2: After removing the retaining clip, pull the lock cylinder straight out from behind the handle assembly @ www.autozone.com
 
AutoMD Verified Customer
AutoMD obtained proof this customer interacted with the shop.