Auto Answers » Preventive Maintenance » Chrysler » Page 19

Chrysler preventive maintenance repair questions and answers

Post your Chrysler preventive maintenance question or share what you know by answering questions

Browse Chrysler Categories

355 Questions
Sort by:
  • Will
    Will - 1990 Chrysler Imperial - Preventive Maintenance - 1/5/2011
    How do i get my window to raise when using the switch doesnot work
    Problem is intermittent. happens frequentls - happens when driving and or stopped and temperature no factor seemingly. no warning lights. no check engine lights. this is an electric problem i believe. at times you can take the key out of the ignition switch and ...
     
    • david
      1/5/2011 david
      take door panel off find motor plug unplug motor use jumper cables pos on one side neg on other it will go up or down switch wires it will go other way if motor is good that will tell you it window switch or wiring problems
    • Nissan Technical Advisor
      Is all your windows doesn't work or it's just one window? If only one, it's more likely a fuse or wiring connection, loose wire or there's a high resistance in the wiring. Motor and cable problem can also be the cause but must trace first if the wiring is ok. A continuity test should be done to determine if wiring is ok or there's a resistance in it. The window switch should be checked also if faulty.
  • Pam
    Pam - 2006 Chrysler Town & Country - Preventive Maintenance - 1/4/2011
    I have no heat or defroster on driver side of vehicle. The blower works just fine
    Before the cold weather set in, when I would use the ac there was a noise like the door (?) was trying to open (clicking) Thank you Pam
     
    • HKS Guy
      1/4/2011 HKS Guy
      Blend door concern, its stuck, you have to remove a part of your dashboard to locate it, its a black rectangular piece of plastic that swivels to let either cold/hot air out. on most cars, their is a panel under the passenger side of the dash and glove box. Just a couple of screws in the front side of it to take it off. You will see a door that lets your heat come through and right up above it is the actuator. It has a plug running to it, so follow your wires and they will lead you to it.
  • tricia sanders
    tricia sanders - 1995 Chrysler Concorde - Preventive Maintenance - 1/4/2011
    We have replaced the water pump, the thermostat, the radiator, and the timing belt. IT is still overheating?
    The fans are hard wired to stay on all the time. It has 86000 miles, it ran for over an hour and stayed in the low temps, then when sitting at idle it over heated.
     
    • Nissan Technical Advisor
      Probably cylinder head gasket is damaged. Did you noticed what color the smoke coming out from the exhaust pipe, and the condition of engine oil if it has foam bubbles in it? Worst the cylinder block is cracked but check first the above suggestions.
      Nissan Technical Advisor
      1/4/2011 tricia sanders
      the smoke that comes out the exhaust is the normal color, and barely any, and there is no foam bubbles, and the mechanic that replaced everything said he doesnt think it is the cylinder block, i got the car back from him a week ago and have driven it like a car that has no problems, and then tonight i drove it to a business, it ran for 25 mins while i was in there and my husband stayed in the car, then ran another errand, then went to hardees and waited for them and thats when it over heated.
      Nissan Technical Advisor
      1/4/2011 tricia sanders
      thats when it overheated, so i am at a loss. I really cant afford to take it backt o my mechanic, what they did already cost me 750.
      Nissan Technical Advisor
      With details given above my suggestion is to buy a radiator pressure tester and test the pressure of the radiator, instructions is given by the link. http://www.ehow.com/.../...ssure-tester.html
      If pressure is ok, the nearest possibility is cylinder head gasket is damaged.
  • 300man
    300man - 2009 Chrysler 300 - Preventive Maintenance - 1/3/2011
    How do i change the cabin air fliter
     
    • Nissan Technical Advisor
      Check the a/c air filter cabin in your engine compartment, passenger side of the engine bay against the firewall to find the air inlet box. Press the tabs to slide the cover forward and access the filter. Lift the old filter from the air inlet box and discard it. Insert the new filter with the arrows pointing toward the rear of the vehicle. Press the tabs and pull the cover back to finish.

      Note: Chrysler recommends replacing this filter every 15,000 miles to keep the interior air quality high.
  • Nancy
    Nancy - 2005 Chrysler 300 - Preventive Maintenance - 1/2/2011
    Blinker signal stays on after making a turn, continues to blink
     
    • david
      1/2/2011 david
      you have to turn off your self there is a turn sign cam is broke in sterring colum
    • TechSam
      1/2/2011 TechSam
      Replace the turn signal switch.
    • J and K AUTOMOTIVE TOWING AND REPAIR
      here is how to replace turn signal switch
      1
      Start your vehicle.
      2
      Road test your vehicle.
      3
      Move the turn signal switch to the left and right position.
      4
      Shut off vehicle and disconnect the negative battery cable.
      5
      Remove the steering column plastic trim to gain access to the turn signal switch.
      6
      Unbolt the turn signal switch retaining screws.
      7
      Disconnect the turn signal switch from the wiring harness.
      8
      Remove the turn signal switch from the vehicle.
      9
      Install a new turn signal switch.
      10
      Connect the new turn signal switch to the wiring harness.
      11
      Tighten the turn signal switch retaining screws.
      12
      Reinstall the plastic steering column trim pieces.
      13
      Reconnect the negative battery cable
      14
      Road test the vehicle to verify the repairs made to the turn signal switch............good luck and happy 2011
  • decardos
    decardos - 1993 Chrysler New Yorker - Preventive Maintenance - 1/2/2011
    How do i program a new keyless entry romote to my car?
    HEEEELP! I recently purchased a 1993 chrysler newyorker fifth avenue and i am having the most horrible time with the anti theft system... i ordered a new keyless entry pad from KEYLESSRIDE.COM it came with (suposed) simple direction but not for me. a guy who doesnt ...
     
    • Tifosi
      10/17/2010 Tifosi
      Umm, i dont mean to sound rude but if that happened to me, id call keylessride.com and ask for more specific directions since they are the ones who sold me that device...

      Now, maybe we can do something about it, how about you scan the instruction sheet then post your email and somebody even me might contact you to be able to help you understand the manual.

    • Thomas
      1/2/2011 Thomas
      I had a simular problem with my 93 new yorker 5th ave...got a new remote, and could not make since out of the instructions that came with it. With the help of a Chrysler tech this is the information that I found out on how to program them...on the drivers side of the center console tucked up underneath is a single dark green wire with a female recepicle end on it...ground that out and the locks will cycle, then press any of the buttons on the remote it will program the remote, if you have two of them, do one right after the other...
  • hamilcr2
    hamilcr2 - 2003 Chrysler 300M - Preventive Maintenance - 12/29/2010
    What happens when the wrong oil filter has been put in?
    The wrong oil filter was put in the car. shortly after, the car started making a rattling noise. Car was taken to a mechanic and he noticed pieces of metal were coming out into the oil. The car had been driven in cold weather for about a month with the wrong oil ...
     
    • Nissan Technical Advisor
      I don't believed its ruined due to wrong oil filter. Perhaps the brand or the part number is different from the original filter but if the oil seal/ring is the same size and fitted well there's no problem with it. The problem with your engine is that you did not noticed that the engine ran out of oil maybe due to oil leak from gasket or from the filter itself or it took many months before you changed your engine oil. Low engine fluid damaged the engine parts because of poor lubrication and resulted for parts being chipped and damaged. An engine overhaul and replacement of engine parts will solve the problem or consider buying a new engine.
  • JEFFRO
    JEFFRO - 2004 Chrysler Sebring - Preventive Maintenance - 12/26/2010
    Battery is dead after car sits 6 hours or more.altenator is good.battery changed 3 times.nothing is left on.
    checked fuses under dash, no power with switch off. all lights are off. battery goes dead.
     
    • CVO
      12/26/2010 CVO
      Local auto stores will test your car with their mobile analyzer for free of charge. Give us an update on the developments.
    • david
      12/26/2010 david
      you have to take ground cable off pull test light on battery and clamp on ground close door cut key off all lights then start pull one fuze at a time till light gone off when your test lite goes off fine out what the fuze goes to that where the short or drain is ck alt take wires off to make shur is not the problem
  • Georgia
    Georgia - 2003 Chrysler PT Cruiser - Preventive Maintenance - 12/25/2010
    Heater blowing cool air after radiator was flushed.
     
    • david
      12/25/2010 david
      take heater hose off motor get a coplin to fit garden hose flush one hose at a time till water runs clear there is rust setems in heater core
  • Tony
    Tony - 2000 Chrysler Sebring - Preventive Maintenance - 12/24/2010
    Heat only works when fan is turned on high setting
    Fan motor is now starting to make noise, which is hadn't done in the past
     
  • cindy
    cindy - 2003 Chrysler PT Cruiser - Preventive Maintenance - 12/21/2010
    Headlights dim when at a stop 2003 Dream Cruiser
    When I come to a stop My 2003 Dream Cruiser headlights dim and then start to flicker not sure of the problem any suggestions
     
    • david
      12/21/2010 david
      ck alt make shur it putting out wright voltage
  • sebring00
    sebring00 - 2000 Chrysler Sebring - Preventive Maintenance - 12/20/2010
    Gas guage does not work
    gas guage was working new fuel pump was installed. gas guage does not register amount of gas in tank. If you fill tank gas will overflow and come out
     
    • Bobby
      12/20/2010 Bobby
      if you had the pump replaced then something could have happened to the gauge then or something might be wrong with the circuit. the sensor for the gauge is part of the fuel sending unit, that the fuel pump is attached to. Did you notice this happenign right after the reapir and who did the fuel pump work?

      next don't overflow the tank you are filling it too much cause you probably think there is less fuel in then there is. what is the gauge showing you all the tiume is it always on full or on empty?

      and last this could be a problem with the evap system. if your vehicle is not filling with gas then it may not be venting properly. the vap system vetilates the gas tank this needs to happen like filling up a watter bottle the air needs to come out as you fill it with water. the evap system allows the air out while you fill the tank if the evap system is clogged then the air can't get out and the result is usually gas bubbling out while you try to fill the tank.
  • james
    james - 2001 Chrysler Town & Country - Preventive Maintenance - 12/19/2010
    My daughter tore off some parts from under the van. I need to know what the parts are called.
    The first part is black box with 2 hose ports for the ac and the 2nd is a tube coil for the ac
     
    0 answer
  • Boogie Love
    Boogie Love - 2000 Chrysler Cirrus - Preventive Maintenance - 12/14/2010
    Just put on a thermostat and still not getting any heat just cold air?
     
    • HouseCallAuto
      12/14/2010 HouseCallAuto
      Probably the blend door is not moving and has maybe lost it's calibration. Do this >>

      1. In the inside fuse box, locate the center fuse that sticks out further than the others.

      2. Pull the fuse for 10 seconds and then reinstall.

      3. Start the vehicle and wait for another 10 seconds.

      4. The actuators should automatically run a self calibration.
      HouseCallAuto
      12/15/2010 Boogie Love
      Thank you
  • colbert
    colbert - 2000 Chrysler Concorde - Preventive Maintenance - 12/8/2010
    Power trunk will not open when button is pushed from inside of car or keyless remote
    i changed the batteries in the keyless remote. also the doors will not lock/unlock from the keyless remote
     
    • Nissan Technical Advisor
      Possibility is that the fuse is loose or the security lock system module is not responding. Have it checked by the dealer.