Chrysler body & interior repair questions and answers
Post your Chrysler body & interior question or share what you know by answering questions
Browse Chrysler Categories
752 Questions
-
My front passenger power window will not roll down.. was working...then just quit. Other 3 work finePeter L. - 2005 Chrysler Sebring - Body & Interior - 7/22/2012Figure not the switch....worked slower and slower then quit....passenger switch will not do the job either..motor maybe????-
7/22/2012 CVOCommon Problems
The window motor shorts out and stops working or works very slowly
The window control switch short circuits due to excessive amperage draw
See this .. http://www.2carpros.com/.../...ower-window-motor
-
-
The back door don't open when press the key?jose - 2006 Chrysler Pacifica - Body & Interior - 7/22/2012Lach won't open -
To fix the leaking evap case see additional details.Jack OBrien - 2005 Chrysler Sebring - Body & Interior - 7/22/2012Remove factory drain apparatus and replace with an appropriately fitting tube securely around evaporator outlet tube. I fix.
-
-
7/22/2012 Jack OBrienThe most time consuming part of this repair is cleaning and drying the carpet, padding, and firewall insulator.
7/22/2012 CVO: -)) Thank you Mr Jack.
-
-
Why does my ac blow cold some times and only blow hot air at other timesPaula - 1999 Chrysler Concorde - Body & Interior - 7/21/2012
-
Why does my rear a/c blow hot air?charles travet - 2002 Chrysler Town & Country - Body & Interior - 7/20/2012129000 miles, I had the system evacuated & checked by an a/c mechanic. there are no leaks and the system was charged with recommended amount of freon and oil. the front a/c is cold and the rear a/c is always hot. no warning lights are on . i noticed this in early ...
-
How to replace the third stop light bulbs300 Touring - 2006 Chrysler 300 - Body & Interior - 7/18/2012
-
Fix for A/C evaporator case leak onto passenger side floor?Jack OBrien - 2005 Chrysler Sebring - Body & Interior - 7/17/2012Evaporator drain is working but evap water is also leaking inside where the case meets the firewall at the drain housing area. Any suggestions?
-
7/17/2012 CVODuplicate question. Remove factory drain apparatus and replace with an appropriately fitting tube securely around evaporator outlet tube. I fix.
This credit goes to Mr Jack, thank you Sir.
-
-
-
7/17/2012 CVOSee this repair guide for Ignition Lock Cylinder REMOVAL & INSTALLATION.
CAUTION
The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the air bag or SIR wiring. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
Disconnect and isolate the negative battery cable from the battery.
In order to disarm the air bag system, allow the SIR system capacitor to discharge for at least 2 minutes, before performing any removal procedures.
Remove the screws that secure the parking brake release handle to the instrument panel.
Remove the screws that secure the bottom of the lower steering column cover to the instrument panel.
Disengage the retaining clip that holds the right side of the lower steering column cover to the instrument panel.
Remove the lower steering column cover from the vehicle.
Remove the mounting screws that hold the upper and lower steering column shrouds and remove the lower steering column shroud.
Install the ignition key and turn the key cylinder to the RUN position. This is important because it will not only aid in removal of the ignition lock, but will also place the socket (in the lock cylinder housing) in proper alignment for the installation of the replacement ignition lock.
Press in the lock cylinder retaining tab and remove the key cylinder (ignition lock).
To install:
Install the ignition key into the replacement ignition lock key cylinder. Turn the key to the RUN position. Depress the ignition lock key cylinder retaining tab.
Align the shaft at the end of the ignition lock cylinder with the socket in the end of the ignition lock cylinder housing.
Align the ignition lock cylinder with the grooves in the lock cylinder housing. Push the ignition lock cylinder into the housing until the retaining tab sticks through the opening in the lock cylinder housing.
Turn the ignition key to the OFF position and remove the key.
Install the lower steering column shroud and install the mounting screws.
Place the lower steering column cover into correct position on the lower instrument panel and engage the clip that secures the right side of the cover to the instrument panel.
Install the lower steering column mounting screws.
Install the mounting screws that hold the parking brake release handle to the instrument panel.
Reconnect the negative battery cable.
FYI. http://www.autozone.com/.../...rGuideContent.jsp
-
-
A/c stuck in heater mode, only hot air 2000 Chrysler 300mDee - 2000 Chrysler 300M - Body & Interior - 7/16/2012
-
7/11/2012 BackYardMechanicYou might need another console to replace the one you got now. Switch may be broken. -
-
-
Dash light don't come onFreddie Sims - 2004 Chrysler Pacifica - Body & Interior - 7/13/2012The dash light and the radio won't light up -
How do I fix my backseat? It is at an angle & when you use power adjuster, it doesn't move it back.Steve - 2008 Chrysler Town & Country - Body & Interior - 7/12/2012-
7/12/2012 jdlI'd have to remove seat and take look. If the seat has a motor for each side, to move the seat forward and backward, one motor may have a problem? Or a problem with wiring circuit for motor.
-
-
My horn is not working???edna - 1990 Chrysler Imperial - Body & Interior - 7/12/2012they tell me it is my fuse, but i do not know where it is???-
7/12/2012 jdlIt should be fuse # 13 in fuse box. The fuse box is in the glove box.
http://postimage.org/image/3yhemgb09/
-
-
Why is my blower motor working sometimes but not working other times?BJohn - 2005 Chrysler Pacifica - Body & Interior - 7/12/2012The blower motor works fine sometimes,not at all other times, and not at full speed other times. After a google search I thought it must be the blower motor resistor but after putting a new one on it didn't help. What else could it be?
-
Why won't fog light go off after light switch is turned offyaya - 2004 Chrysler PT Cruiser - Body & Interior - 7/11/2012if i don't take the fuse out, the battery runs down-
7/11/2012 CVOSee this Headlight Switch
Part Number: SW2287
Warranty: Limited Lifetime
Application: With fog lamps
http://www.autozone.com/.../N-jlfalZ9ciaj
Check the headlight switch.
7/11/2012 CVOAnd the wiring harness for any physical damaged.
-
-
Inside cabin fan::What is preventing the inside cabin fan from being regulated? The fan blows on high level only.naneek - 2003 Chrysler Town & Country - Body & Interior - 7/10/2012
